亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Sudan

Release time:2023-11-12 15:28:20 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Sudan synchronous hydraulic cylinder

(Sudan synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Sudan,because of high work efficiency,long service life,smooth movement.So our company has designed synchronous hydraulic cylinder for customers from Sudan.

Introduction to synchronous hydraulic cylinder:

When the control pressure of the hydraulic system is too low, the synchronous hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

When using the synchronous hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the synchronous hydraulic cylinder block. If the synchronous hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the synchronous hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the synchronous hydraulic cylinder, so that the working efficiency of the synchronous hydraulic cylinder is reduced.

The machining accuracy of the synchronous hydraulic cylinder depends on the level of equipment, production technology and testing means. synchronous hydraulic cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

When installing the synchronous hydraulic cylinder, the axial ends of the synchronous hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the synchronous hydraulic cylinder, there is axial expansion. If the two ends of the synchronous hydraulic cylinder are fixed, all parts of the synchronous hydraulic cylinder will be deformed. When disassembling the synchronous hydraulic cylinder, it is strictly forbidden to hammer the synchronous hydraulic cylinder and the piston surface, such as the synchronous hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about synchronous hydraulic cylinder:

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操逼一区二区视频免费观看| 大骚逼操逼视频在野外操骚逼| 超碰在线精品一区日韩| 欧美日逼黄片| 青青综合色| 九九性偷拍肏逼| 国产在线观看免费AV| 鸡巴插入逼里面,在线观看| 日韩十一区| 东南亚免费一级尿尿视频 | 极品AV在线播放| 哪里看日韩性爱视频| 偷拍台湾妹0| 免费男女乱淫视频| 五月激情网在线视频| 人妻-区二区三区无码,免费-区| 嗯嗯啊啊好湿好爽视频| 老熟女高潮喷浆| 秋霞网午夜一区二区| 91九色国产大鸡吧| 上犹县| 久久久久久性生活| 在线成仁一区| 在线视频中文字幕一区二区三| 少妇翘臀视频在线播放| 比被插的视频| 人人妻人人人人一区二区三区| 久一亚洲国产精品| 人妻91一区二区三区| AV在线播放大香蕉| 91AV导航| 在线制服丝袜诱惑| 视频一区 视频二区 视频三区 字幕 | 人人人人操操人人人| 男生舔女生的逼91网站| 日韩成人性网| 人人艹日本| 日韩岛国国产精品| 欧美 日韩 另类 字幕中文| 人妻斩一区十二区| av老司机 在线播放|