亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Poland

Release time:2023-11-12 15:28:39 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Poland push plate cylinder

(Poland push plate cylinder,produced by Hengyu Hydraulic Co., Ltd)

push plate cylinder are widely used in Poland,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed push plate cylinder for customers from Poland.

Introduction to push plate cylinder:

If the push plate cylinder slips or crawls, please check whether there is astringency inside the push plate cylinder, because the internal parts of the push plate cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the push plate cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the push plate cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

The scar on the sliding surface of the push plate cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the push plate cylinder wall. Therefore, before installation, these scars must be fully repaired.

In order to ensure the service life of the push plate cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the push plate cylinder, causing damage to the seal and causing leakage in the push plate cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

The piston rod and guide sleeve function of the push plate cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

Answers to some questions about push plate cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美黑人少妇高潮喷水| 一区二区欧美视频中文精品一品精品| 婷婷爱五月一区| 看操日逼| 一二三四区无线免费视频| 白丝美女被操到高潮| 一二三四五日本视频免费观看| AV操B女人| 九九精品蜜臀| 中文字幕日韩精品一区欧美爆乳 | 欧美视频89| 丁香中文字幕视频| 韩国性综合网| 熟女少妇一区二区三区四区-精品国语 | www91一区二区三区| 操美女真爽| 亚洲御姐一区在线| 亚洲国产最新一卡二卡三卡四卡| 操小骚女人的骚逼逼| 欧美性生活在线不卡播放| 美国大鸡巴一级A电视播放| 日韩视频欧美做爱网站| 麻豆乱老熟女视频一区| 久热精品视频1| av在线亚洲一区| 大黑屌狂操巨乳肥臀少妇| 嗯嗯难受久久| 亚洲丝袜诱惑一区| 蜜臀久久9999精品久久宅男 | 美女高潮喷水精品素人| 少妇视频爽爽网| 啊呃呃呃啊啊嗯嗯视频| 日韩 不卡 在线| 性爱激情网| 台湾久久小视频| 中文字幕公寓一区二区| 91免费看nd国产| 亚州少妇女亚州精品| 宁强县| 超碰免费人妻系列| 美女100%无挡网站在线看|