亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift cylinder Sold to Spain

Release time:2023-11-14 08:41:51 Hits: Current position: Home > News

This article mainly introduces:

Spain hydraulic cylinder,forklift cylinder manufacturer,forklift cylinder

Spain forklift cylinder

(Spain forklift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift cylinder are widely used in Spain,because of no need for deceleration device,long service life,smooth movement.So our company has designed forklift cylinder for customers from Spain.

Introduction to forklift cylinder:

If the forklift cylinder slips or crawls, please check whether there is astringency inside the forklift cylinder, because the internal parts of the forklift cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the forklift cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the forklift cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

The forklift cylinder should be vented: when the forklift cylinder is installed or parked for a long time to work again, the air will penetrate into the forklift cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the forklift cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the forklift cylinder, the oil is best entered and discharged from the highest point of the forklift cylinder. forklift cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Regular maintenance of the forklift cylinder includes: regular tightening, forklift cylinder fastening screws and gland screws, forklift cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the forklift cylinder once a year. Clean regularly, the forklift cylinder is cleaned every other year, and the seals are replaced while cleaning.

When the control pressure of the hydraulic system is too low, the forklift cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about forklift cylinder:

What is the rated pressure of the general cylinder?
This depends on the model of the cylinder, 1. The rated pressure of the light tie rod cylinder is 7 series 7MPa and 14 series 14MPa. 2. Rated pressure of engineering cylinder 16MPa. 3. Rexroth type metallurgical cylinder rated pressure 250MPa.

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕在线一区二三区| 青青操原在线视频播放| 国产女主播和帅哥在线播放| 日韩性爱一级片欧美性爱一级片| 日韩三级精品人妻| 午夜福利入口三| 大伊香蕉在线| 国产最新成人av| 日本伊人自拍偷拍| 先锋影音av蜜臀麻豆| 老司机精品视频无码一区二区| 骚穴视频大学生| 国产内射在线传媒| 视频性交色婷婷| 中文字幕之亚洲有码| 草大逼视频| 天天操人人操91| 中文字幕亚洲三| 红桃AV日韩精品| 性激情啪啪一二三四五六区| 超碰青娱乐日韩精品欧美| 日本人妻制服丝袜诱惑视频@| 蜜臀色一区二区精品| 麻豆合集在线观看| 亚洲av一二三四五区在线| 操逼视频啊啊叫| 亚洲涩婷婷视频| 美女操逼色| 美女的下面被插网站| 日本自慰一区在线观看| 日日骚,欧美日韩| 欧美精品狠狠躁| 啊啊啊大鸡巴啊啊操啊啊在线欧美| 日本黃色中文字幕| 囯产美女无遮挡免费视频| 国产精品啊啊啪啪| 抽查处女成人免费视频| 天天拍天天色天天爽| 人妻熟妇久久久久| 日本在线大香蕉网| 日本网站熟妇|