亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

Lifting cylinder Sold to Italy

Release time:2023-11-17 13:21:24 Hits:138 Current position: Home > News

This article mainly introduces:

Italy hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Italy Lifting cylinder

(Italy Lifting cylinder,produced by Hengyu Group)

Lifting cylinder are widely used in Italy,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed Lifting cylinder for customers from Italy.

Introduction to Lifting cylinder:

If the seal of the Lifting cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the Lifting cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The quality of the Lifting cylinder can not be ignored in the purchase of the Lifting cylinder. The Lifting cylinder is the main component of the Lifting cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Lifting cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of Lifting cylinder is deep hole processing, which has always troubled the processing personnel.

The internal leakage of the Lifting cylinder should be prevented when the Lifting cylinder is used. The internal leakage of Lifting cylinder includes the leakage caused by excessive wear of Lifting cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about Lifting cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩色图18p| 光棍的日B视频| 国产91视频骚逼| 嗯啊,大鸡吧插穴在线播放| 日韩性插插视频| 日韩操逼视频网| 日本一区免费在线不卡| 成人熟女大屁股无码一区二区三区| 五月婷婷大香蕉AV| 99婷婷中文字幕一区二区三区| 国产成人一二三| 丝袜美女的鸡巴视频| 美女懂得网站| 人妻少妇蜜桃视频欧美一区| 一及黄色大片| 鸡巴日中国美女的屄| 欧美大码女美女操逼视频| 女生白丝被操的视频| 色欲AU精品一区二区| 啊巨久久69| 大美女的逼叫男人操视频| 99精品又硬又粗又黄少妇视频| 大黑鸡巴做爱视频| 国产丝袜传媒一二三区| 成人巨乳福利午夜| 日本有码手机在线观看| 中出人妻免费看| 欧美人妻久久精品| 天天射天天操天天插天天日天天干| 夜夜爽夜夜干| 欧美视频手机在线观看| 久久精品亚洲传媒视频| 蜜乳AV一区二区三区四区| 激情都市中文字幕1区2区3区| 日韩成人免费播放器一区二区| 青青草原亚洲天堂欧洲| 97蜜臀人人| 亚洲一区二区三区不卡岁禁| 国产老熟女导航| 亚洲AV无码秘 一区二区三区、| 操逼逼亚洲国产|