亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Egypt

Release time:2023-11-24 08:39:24 Hits: Current position: Home > News

This article mainly introduces:

Egypt hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Egypt trunnion cylinder

(Egypt trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Egypt,because of high work efficiency,long service life,excellent fatigue and impact resistance.So our company has designed trunnion cylinder for customers from Egypt.

Introduction to trunnion cylinder:

The internal leakage of the trunnion cylinder should be prevented when the trunnion cylinder is used. The internal leakage of trunnion cylinder includes the leakage caused by excessive wear of trunnion cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The oil trunnion cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

When the trunnion cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the trunnion cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil trunnion cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical trunnion cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the trunnion cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

At the rated pressure, the thrust of the trunnion cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the trunnion cylinder is related to the diameter of the trunnion cylinder, but not to the stroke of the trunnion cylinder. Moreover, the larger the trunnion cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the trunnion cylinder.

Answers to some questions about trunnion cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产av一品二品精品| 校园激情狠狠干| 女生被操到爽| 中日美黄片| 欧美日韩插入| 91美女偷拍1区| 悠亚av在线| 少妇视頻网| 大鸡巴成人在线视频| 抽插视频观看| 去干网最新久久| 性操B美女| 黑丝美女被操的网站| a亚洲s大片一区在线| 成人开心福利在线| 大鸡巴操瑜伽美女视频| 欧美视频八九区| 化德县| 亚洲免费视频一区二区三| 黑人大屌狠操日本女人骚逼录像| 国产精品自拍亚瑟视频| 在线观看大鸡巴C| 中国色综合| 国内老熟女盗摄一区二区三区在线| www.色五月婷婷| 亚洲色导航综合| 韩国三级在线一区| 嗯啊操干视| 啊啊啊.插小逼逼视频| 好湿好多水好想要在线视频| 嗯啊嗯啊h视频| 啊好大快操进来操死骚逼| 偷拍日本美女操B操B尿尿| 多国操逼视频免费| 一七六九1769视频| 深爱激情A网| 黑人巨吊av不卡| ,97大香蕉视频| 韩国三级片在线精品视频| 中文字幕久久一区二区三区| 真正的中出在线播放|