亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Republic of Lithuania

Release time:2023-11-24 16:13:34 Hits: Current position: Home > News

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Republic of Lithuania track steering cylinder

(Republic of Lithuania track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Republic of Lithuania,because of no need for deceleration device,long service life,smooth movement.So our company has designed track steering cylinder for customers from Republic of Lithuania.

Introduction to track steering cylinder:

The method of sleeve track steering cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the track steering cylinder can be significantly improved by rolling in the finishing of the inner holes of the track steering cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

The advantages and disadvantages of the track steering cylinder: the surface of the track steering cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the track steering cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

When the track steering cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the track steering cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

track steering cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the track steering cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about track steering cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
骚逼美女大鸡鸡国产av| 91人妻骚妇在线观看 | 青青草原国产一区在线| 九九日本黄色| 中文精品一区二区三区| 日韩二区第五页| 操骚逼死哦视频视频| 中出性视频,| 嗯啊后入嗯视频| 91人妻丰满熟妇Aⅴ无码| 日本大鸡吧插骚逼视频 | 日韩丝袜熟女中文| 一区二区制服诱惑| 中文字幕高清黄| 嗯嗯啊啊嗯嗯啊啊视频| 色五月 99| 亚洲国产另类在线观看| 欧美亚洲日本韩国综合网| 成人97大香蕉| 午夜在线视频18| 国产模特肛交| 热久久这里精品视频| 野外社区AV| 人妻丝袜一区二区三区免费| 插我一区二区在线观看| 啊啊啊啊啊啊好爽| 熟女少妇一二区| 国产夫妻自拍的啪啪啪啪| 色诱免费少妇视频在线| 口爆视频91在线| 操操骚逼视频| 来点大鸡巴操小嫩逼一操操出白浆的 | 美女在线观看国产福利| 亚洲伦理母乳片| 嫩逼喷白浆视频| 麻豆91在线视频| 夫妻性生活一级片一区二区三区 | 插逼逼站| 亚洲岛国精品| 超碰成人青青草| 长腿制服美女吹鸡巴|