亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Tanzania

Release time:2023-11-27 15:08:25 Hits: Current position: Home > News

This article mainly introduces:

Tanzania hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Tanzania swager cylinder

(Tanzania swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Tanzania,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed swager cylinder for customers from Tanzania.

Introduction to swager cylinder:

swager cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the swager cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

The oil swager cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

swager cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

If the swager cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the swager cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow swager cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the swager cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the swager cylinder includes the leakage caused by excessive wear of the swager cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and swager cylinder, and the phenomenon of "pulling the swager cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about swager cylinder:

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产肥臀熟女福利视频| 日本伊人三区| 国产成人a免费| 日韩一区在线视频| 欧美亚洲点击进入| SS资源站| 国产高清在线观看美女网站| 嗯操我的逼视频| 欧美少妇肏屄视频| 日本中文字幕有码久| 狂操美女小骚逼逼| 非洲一区视频| 操中国B| 操日本美女操逼动漫| 香蕉网999| 黑人超大屌日本女人三级片影片网站| 大吊插嫩逼一区二区三区免费| 乱丝袜久久老师| 婷婷五月天,欧美熟女| 亚洲精品五码精品| 欧洲最新无码| 在线免费欧美视频 | 五月天伊人激情| 精品 一区二区三区| 国产麻豆又黄又粗老师| 鸡巴搞美女的p| 超碰公开在线97| 小黄片污污在线观看高h np| 人人色天天干一二三区| 精品名女久久一区二区三区| 欧美最大胆视频| 海门市| 日本 亚洲 综合 婷婷| 啊啊肏我啊疼在线视频| 和硕县| 少妇蜜臀aV一区二区三区| 国产日韩欧美成人在线观看视频| 美女日屄骚逼| 被大鸡吧操小逼潮吹亚洲区| 亚洲草逼AV| 九九视频88|