亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Switzerland

Release time:2023-11-09 08:45:52 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Switzerland stern plate hydraulic cylinder

(Switzerland stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Switzerland,because of long service life,smooth movement,high work efficiency.So our company has designed stern plate hydraulic cylinder for customers from Switzerland.

Introduction to stern plate hydraulic cylinder:

stern plate hydraulic cylinder can not drive the load troubleshooting: oil pressure is too low. stern plate hydraulic cylinder selection specifications are too small. Leakage in stern plate hydraulic cylinder or associated hydraulic system element.

The assembly work of the stern plate hydraulic cylinder has a great impact on the quality of the stern plate hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When purchasing the stern plate hydraulic cylinder, try to clarify the following parameters of the stern plate hydraulic cylinder: A. stern plate hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or stern plate hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right stern plate hydraulic cylinder type can be found accurately and quickly.

The piston rod of the stern plate hydraulic cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

Answers to some questions about stern plate hydraulic cylinder:

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美黑人大鸡巴操逼| 大交香蕉一区二区三区四区五区免费| 第一二三区骚逼| 抽插无码高清| 大鸡巴操嫩逼免费视频| 欧美,国产视频| 美女国产喷水全裸欧美| 啊啊啊不要再操了好爽啊视频软件| 大鸡吧操逼过瘾视频| 女人免费小视频| 林州市| 69AVXXX白浆| 久久青青草原国产精品乐播| 无码北岛玲一本道| 欧亚色图老熟女视频图片| 韩国美女尤物操小骚逼逼| 欧美黑人少妇高潮喷水| 色哟哟.apk| 殴美日韩五月婷婷| 操死我主人在线视频播放| 五月久久在线免费观看| 嗯啊黑屌好大| 白白操操| 黑丝美女被操网站视频| 插大进入视频| 丰满尤物久久| 国产探花在线观看| 亚洲成熟日本女人毛茸茸| 日本熟妇色手机在线| 男生操美女逼视频免费| 九九热在线免费视频| 一本道av中文字幕| 少妇嫩穴综合| 18国产在线观看| 老女人骚骚视频| 国产微拍福利一区二区在线观看| 偷拍台湾妹0| 精品熟女一区二区三区四区| 国产美女爽到喷出水91| 96午夜视频| 三上悠亚AV一区二区三区|