亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Puerto Rico

Release time:2023-11-09 08:45:55 Hits: Current position: Home > News

This article mainly introduces:

Puerto Rico hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Puerto Rico synchronous hydraulic cylinder

(Puerto Rico synchronous hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

synchronous hydraulic cylinder are widely used in Puerto Rico,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed synchronous hydraulic cylinder for customers from Puerto Rico.

Introduction to synchronous hydraulic cylinder:

In order to ensure the service life of the synchronous hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

If the piston rod and synchronous hydraulic cylinder are stuck or the synchronous hydraulic cylinder is blocked, at this time, no matter how to operate, the synchronous hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the synchronous hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the synchronous hydraulic cylinder is customized, if there are high requirements for the quality of the synchronous hydraulic cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the synchronous hydraulic cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the synchronous hydraulic cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

If the synchronous hydraulic cylinder slips or crawls, please check whether there is astringency inside the synchronous hydraulic cylinder, because the internal parts of the synchronous hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the synchronous hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the synchronous hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about synchronous hydraulic cylinder:

How to judge the failure of forklift hydraulic cylinder?
The common faults of the hydraulic cylinder of forklift truck are mainly crawling, insufficient thrust, working speed decline or even stop. Generally, crawling occurs at low speed. The main reason is that the air stored in the cylinder is not cleared. In addition, excessive or uneven mechanical friction can also cause crawling. Such as the piston and the piston rod different heart, the piston rod full length or local bending, the cylinder hole straightness is poor, the cylinder is drum shaped or has a large taper, the cylinder thin finish decline or produce hair, the cylinder installation accuracy is out of whack, the piston rod nuts at both ends of the screw too tight to make its concentricity is poor, the oil seal screw too tight friction is too large, will cause crawling.

What should we pay attention to when using the cylinder?
When using the cylinder, we should pay attention to the environment and temperature in which it is located as follows: 1. Before working, the hydraulic cylinder must carry out several reciprocating movements under low pressure (greater than the starting pressure), and work normally after removing the gas in the cylinder. 2. Precautions when removing the hydraulic cylinder: ① The pressure in the hydraulic circuit is reduced to zero before disassembly. ② The screw thread at the top of the piston rod should be prevented from damage when disassembling. ③ Due to the different structure and size of the hydraulic cylinder, the order of disassembly is also slightly different. Generally, the fastening bolt of the end cover should be loosened first. Internal card chain card key application special tools.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本成人午夜的福利视频| www.精品久久一区二区三区三州| 一线人妻区| 大鸡巴操大黑逼免费视频| 美女隐私无遮挡免费看自拍无男人| 欧美日韩一级视频观看| 人妻不卡一区二区三区三区| 麻豆视频天美91视频| 国产精品视频有码| 得得干永久免费视频| 日本成熟女性一区二区三区| 91人妻偷拍| 国产窵肏逼视频| 99久久婷婷免费精品视频| 精品国产美女福领在线| 久久成人精品日韩| 桃乃木香奈在线亚洲| 熟女一区二区三区五区| 日本丰满大乳人妻无码香港电视| 老司机精品激情视频搜索| 大香蕉久久视频福利导航| 要我,国产视频| 亚洲男人皇宫| 日韩三级性爱视频网站| 国产淫妇重口另类直播在线| 快来操我啊啊啊啊啊啊视频| 99热在线精品se热| 久久穴热| 老外大鸡巴插女| 女人色骚色人碰| 日本人妻与黑人XXX| 抽插小穴出水| 自拍五月网| 99操B视频| 熟女倶乐部偷拍人妻av| 成人电影日韩大香蕉| 鸡巴S在线观看| 日本三级片免费偷拍| 亚洲国产精品日韩av专区| 日韩中文字幕在线观看视频一区二 | 大香蕉色欲|