亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Switzerland

Release time:2023-11-12 15:26:02 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Switzerland track steering cylinder

(Switzerland track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Switzerland,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed track steering cylinder for customers from Switzerland.

Introduction to track steering cylinder:

The track steering cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

When the track steering cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the track steering cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the track steering cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the track steering cylinder can meet the requirements by grinding. However, the life and reliability of this repair track steering cylinder are not high.

track steering cylinders in series, parallel and series parallel. Series: In the track steering cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the track steering cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the track steering cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the track steering cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

After chrome plating of the piston rod of the track steering cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about track steering cylinder:

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美日逼欧美| 台湾娱乐性综合中文网22| 操女人屁眼成人在线| 亚洲国产欧美日韩另类| 男生桶爽女生视频在线观看| 亚洲男女日B成人免费视频| 欧美caocao| 奶茶美女久久久| 专操老熟女五十| 大香蕉 福利 视频 导航| 啊啊啊啊啊啊视频一区| 国产在线观看免费AV| 操美女网站在线看| 大香蕉福利视频免费看| 国产欧美日韩一级操逼不卡 | 欧美夫妻性生活视频在线播放| 又大又粗又硬又爽网站| 亚洲∨∧| 黑丝美女被我操| 久久婷婷东京热| 两个男人的毛片小视频| 一本岛在线色AV| 蜜臀午夜福利| 超碰特在线| 男女羞羞一区| 女视频在线网站| www.超碰资源站| 昭通市| 亚洲另类熟女15p| 亚洲熟人妻在线| 国产av区一区二区| 操逼视频网站在线观看免费| 福利吧在线小视频| 大鸡巴插插骚逼好舒服啊啊视频| 嗯嗯嗯国产在线观看| 福利视频三区欧美| 啊呃呃呃啊啊嗯嗯视频| 啊,不要,我好疼在线视频| 五月天资源久久| 美女插鸡吧久久久久| 大黑屌欧美日韩国产美乳翘臀|