亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to New Zealand

Release time:2023-11-12 15:26:17 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

New Zealand stroke adjustable cylinder

(New Zealand stroke adjustable cylinder,produced by Hengyu Group)

stroke adjustable cylinder are widely used in New Zealand,because of smooth movement,simple structure and reliable operation,powerful torque.So our company has designed stroke adjustable cylinder for customers from New Zealand.

Introduction to stroke adjustable cylinder:

stroke adjustable cylinder and hydraulic station selection: Select the type and structure of the stroke adjustable cylinder according to the operation requirements of the main engine. According to the external load force borne by the stroke adjustable cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the stroke adjustable cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the stroke adjustable cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the stroke adjustable cylinder, the diameter of the piston and the piston rod.

Do not enter foreign bodies when installing the stroke adjustable cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

The repair method of stroke adjustable cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

If the stroke adjustable cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the stroke adjustable cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow stroke adjustable cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the stroke adjustable cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the stroke adjustable cylinder includes the leakage caused by excessive wear of the stroke adjustable cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and stroke adjustable cylinder, and the phenomenon of "pulling the stroke adjustable cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about stroke adjustable cylinder:

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴操B无码视频免费在线播放| 极品人妻美妇| 大黑鸡巴艹逼欧美| 做暧暧小视频久久九九青青操 | 人妻爆肏中出| 免费看操美女的真逼视频| 欧美国产少妇视频网站| 视频 五月婷婷| 欧美日韩精品少妇人妻| 黑人日韩性生活视频| 操老太太,操老太太| 亚洲自拍亚洲视频| 婷婷五月 色| 日本免费看啪啪视频| 五月综合之激情91| 美国少妇自慰| 大胆美女爱上大吊鳮巴男生| 91国产黄片| 欧美曰骚逼| 天天操美女逼天天色| 亚洲性爱图片网| 美女诱惑中文字幕| 骚逼不着我们的大鸡巴操骚逼| 婷婷五月天激情成人在线播放| 亚洲高清免费一二三区老司机| 丰满人妻激情网| 美女视频自拍电影网站| 亚洲成人入口| 于都县| 国产又黄的视频| 人人射天天操人人妻| 好疼好爽啊啊免费黄片视频在线观看 | 台湾综合娱乐久久| 国产骚逼操| 超碰熟女大香蕉| 大美女后操大操逼| 日本最新免费 欧美一区二区三区| 91 国产 爽 黄 喷水| 日韩新伦理视频在线| 五月丁香色综合久久蜜臀AV| 一级一级一级毛片|