亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to France

Release time:2023-11-20 09:49:09 Hits: Current position: Home > News

This article mainly introduces:

France hydraulic cylinder,tension cylinder manufacturer,tension cylinder

France tension cylinder

(France tension cylinder,produced by Hebei Hengyu company)

tension cylinder are widely used in France,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed tension cylinder for customers from France.

Introduction to tension cylinder:

The assembly work of the tension cylinder has a great impact on the quality of the tension cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

If the tension cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the tension cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The repair method of tension cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about tension cylinder:

How big is the motor and oil pump for the 80 cylinder?
Pump motor selection is not only related to cylinder diameter but also speed system, it is recommended to provide system diagram and speed requirements, generally speaking, most of the 80 cylinder on the market is equipped with 3-4KW motor, 10-20 oil pump.

What are the reasons why the hydraulic cylinder action is slower than normal?
There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system under the pressure state is consistent with the initial setting. Before measuring the pressure, it is best to check the hydraulic oil and suction oil filter and replace or clean it. Second, check the main relief valve of the reversing control multiway valve to see if there is damage or foreign matter blocking, and clean it. If your pump is a gear pump, the problem should generally be small. Second, look at traffic. There is no leakage in the cylinder, leakage in the reversing valve spool and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
啊啊啊啊啊好舒服视频在线观看| 操B免费看| 亚洲二人妖性爱| 看欧美俄罗斯日韩美女逼啪啪啪 | 熟女一区二区三区在线| 巴怪物操逼视频网站在线播放| 精品黑人巨吊| 操广州熟女露脸| 欧美美女极品中文字幕一区二区三区四区 | 午夜小视频福利在线播放| 91精品日韩视频| 欧美女人大黑老B| 熟女真一区二区三区SXXHD| 琪琪视频一区二区| 丰满人妻一区三区| 美女操大逼视频免费观看| 激情综合综合网| 差逼逼视频| 林ゆな人妻一区二区| av一级无码一区| 欧美自拍偷拍导航| 操一下在线视频播放| 乱码婷婷五月| 色哟哟在线观看入口| 岛国免费在线播放| 色婷婷免费| 91在线制服丝袜| 一区二区榴莲视频在线观看| 五十路六十路亚洲色| 少妇小网站| 日韩第一精品区| 小美女的小穴| 五十路熟女A∨视频| www,日比| 不卡亚洲操逼网| www.青青草原视频国产| 吃瓜av一区二区| 老司机在线激情在线视频 | 欧美骚逼骚逼骚逼骚逼骚| 五月婷婷久久久开心| 大鸡巴强奸少妇|